? semiconductor components industries, llc, 2005 december, 2005 ? rev. 1 1 publication order number: mac16hc/d mac16hcd, mac16hcm, mac16hcn preferred device triacs silicon bidirectional thyristors designed primarily for full-wave ac control applications, such as motor controls, heating controls or dimmers; or wherever full?wave, silicon gate?controlled devices are needed. features ? high commutating di/dt and high immunity to dv/dt @ 125 c ? uniform gate trigger currents in three quadrants, q1, q2, and q3 ? blocking voltage to 800 volts ? on?state current rating of 16 amperes rms at 80 c ? high surge current capability ? 150 amperes ? industry standard to?220ab package for ease of design ? glass passivated junctions for reliability and uniformity ? pb?free packages are available* maximum ratings (t j = 25 c unless otherwise noted) rating symbol value unit peak repetitive off?state voltage (note 1) (t j = ?40 to 125 c, sine wave, 50 to 60 hz, gate open) mac16hcd mac16hcm mac16hcn v drm, v rrm 400 600 800 v on?state rms current (full cycle sine wave 50 to 60 hz; t c = 80 c) i t(rms) 16 a peak non-repetitive surge current (one full cycle, 60 hz, t j = 125 c) i tsm 150 a circuit fusing consideration (t = 8.33 ms) i 2 t 93 a 2 sec peak gate power (pulse width 1.0 s, t c = 80 c) p gm 20 w average gate power (t = 8.3 ms, t c = 80 c) p g(av) 0.5 w operating junction temperature range t j ?40 to +125 c storage temperature range t stg ?40 to +150 c maximum ratings are those values beyond which device damage can occur. maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. if these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. v drm and v rrm for all types can be applied on a continuous basis. blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. triacs 16 amperes rms 400 thru 800 volts to?220ab case 221a?09 style 4 1 http://onsemi.com mac16hcxg ayww marking diagram x = d, m, or n a = assembly location y = year ww = work week g = pb?free package 2 3 mt1 g mt2 pin assignment 1 2 3 gate main terminal 1 main terminal 2 4 main terminal 2 preferred devices are recommended choices for future use and best overall value. device package shipping ordering information mac16hcd to?220ab 50 units / rail mac16hcn to?220ab 50 units / rail mac16hcdg to?220ab (pb?free) 50 units / rail mac16hcng to?220ab (pb?free) 50 units / rail mac16hcm to?220ab 50 units / rail MAC16HCMG to?220ab (pb?free) 50 units / rail
mac16hcd, mac16hcm, mac16hcn http://onsemi.com 2 thermal characteristics characteristic symbol value unit thermal resistance, junction?to?case junction?to?ambient r jc r ja 2.2 62.5 c/w maximum lead temperature for soldering purposes 1/8 from case for 10 seconds t l 260 c electrical characteristics (t j = 25 c unless otherwise noted; electricals apply in both directions) characteristic symbol min typ max unit off characteristics peak repetitive blocking current t j = 25 c (v d = rated v drm , v rrm , gate open) t j = 125 c i drm , i rrm ? ? ? ? 0.01 2.0 ma on characteristics peak on?state voltage (note 2) (i tm = 21 a peak) v tm ? ? 1.6 v gate trigger current (continuous dc) (v d = 12 v, r l = 100 ) mt2(+), g(+) mt2(+), g(?) mt2(?), g(?) i gt 10 10 10 16 18 22 50 50 50 ma holding current (v d = 12 v, gate open, initiating current = 150 ma) i h ? 20 50 ma latch current (v d = 12 v, i g = 50 ma) mt2(+), g(+) mt2(+), g(?) mt2(?), g(?) i l ? ? ? 33 36 33 60 80 60 ma gate trigger voltage (continuous dc) (v d = 12 v, r l = 100 ) mt2(+), g(+) mt2(+), g(?) mt2(?), g(?) v gt 0.5 0.5 0.5 0.80 0.73 0.82 1.5 1.5 1.5 v dynamic characteristics rate of change of commutating current (v d = 400 v, itm = 6a, commutating dv/dt = 20 v/ s, cl = 10 f gate open, t j = 125 c, f = 250 hz, with snubber) ll = 40 mh (di/dt)c 15 ? ? a/ms critical rate of rise of off?state voltage (v d = rated v drm , exponential waveform, gate open, t j = 125 c) dv/dt 750 ? ? v/ s repetitive critical rate of rise of on-state current ipk = 50 a; pw = 40 sec; dig/dt = 200 ma/ sec; f = 60 hz di/dt ? ? 10 a/ s 2. pulse test: pulse width 2.0 ms, duty cycle 2%.
mac16hcd, mac16hcm, mac16hcn http://onsemi.com 3 + current + voltage v tm i h symbol parameter v drm peak repetitive forward off state voltage i drm peak forward blocking current v rrm peak repetitive reverse off state voltage i rrm peak reverse blocking current voltage current characteristic of triacs (bidirectional device) i drm at v drm on state off state i rrm at v rrm quadrant 1 mainterminal 2 + quadrant 3 mainterminal 2 ? v tm i h v tm maximum on state voltage i h holding current mt1 (+) i gt gate (+) mt2 ref mt1 (?) i gt gate (+) mt2 ref mt1 (+) i gt gate (?) mt2 ref mt1 (?) i gt gate (?) mt2 ref ? mt2 negative (negative half cycle) mt2 positive (positive half cycle) + quadrant iii quadrant iv quadrant ii quadrant i quadrant definitions for a triac i gt ? + i gt all polarities are referenced to mt1. with in?phase signals (using standard ac lines) quadrants i and iii are used.
mac16hcd, mac16hcm, mac16hcn http://onsemi.com 4 120 t j , junction temperature ( c) figure 1. typical gate trigger current versus junction temperature t j , junction temperature ( c) i gt , gate trigger current (ma) v gt , gate trigger voltage (volt) ?40 ?10 20 50 80 110 125 100 1 q3 q1 q2 1.10 0.40 q1 q2 q3 figure 2. typical gate trigger voltage versus junction temperature holding current (ma) t j , junction temperature ( c) mt2 positive mt2 negative latching current (ma) t j , junction temperature ( c) figure 3. typical holding current versus junction temperature figure 4. typical latching current versus junction temperature ?25 5 35 65 95 10 100 1 10 100 1 10 ?40 ?10 20 50 80 110 125 ?25 5 35 65 95 ?40 ?10 20 50 80 110 125 ?25 5 35 65 95 0.50 0.60 0.70 0.80 0.90 1.00 ?40 ?10 20 50 80 110 125 ?25 5 35 65 95 q2 q1 q3 figure 5. typical rms current derating i t(rms) , rms on-state current (amp) 125 110 95 80 12 10 8 6 4 2 0 t c , case temperature ( c) figure 6. on-state power dissipation i t(av) , average on-state current (amp) 12 10 8 6 4 2 0 18 16 14 12 10 8 6 4 2 p (av) , average power dissipation (watts) 0 180 70 24 dc dc 60 90 120 180 30 105 90 75 115 100 85 120 16 14 90 60 , 30 14 16 20 22
mac16hcd, mac16hcm, mac16hcn http://onsemi.com 5 figure 7. typical on-state characteristics v t , instantaneous on-state voltage (volts) 100 0 i t , instantaneous on-state current (amp) 0.5 1 1.5 2 2.5 3 3.5 10 1 0.1 maximum @ t j = 125 c typical @ t j = 25 c maximum @ t j = 25 c figure 8. typical thermal response t, time (ms) r(t), transient thermal resistance (normalized) 1 0.1 0.01 10000 1000 100 10 1 0.1
mac16hcd, mac16hcm, mac16hcn http://onsemi.com 6 package dimensions notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. dimension z defines a zone where all body and lead irregularities are allowed. style 4: pin 1. main terminal 1 2. main terminal 2 3. gate 4. main terminal 2 dim min max min max millimeters inches a 0.570 0.620 14.48 15.75 b 0.380 0.405 9.66 10.28 c 0.160 0.190 4.07 4.82 d 0.025 0.035 0.64 0.88 f 0.142 0.147 3.61 3.73 g 0.095 0.105 2.42 2.66 h 0.110 0.155 2.80 3.93 j 0.018 0.025 0.46 0.64 k 0.500 0.562 12.70 14.27 l 0.045 0.060 1.15 1.52 n 0.190 0.210 4.83 5.33 q 0.100 0.120 2.54 3.04 r 0.080 0.110 2.04 2.79 s 0.045 0.055 1.15 1.39 t 0.235 0.255 5.97 6.47 u 0.000 0.050 0.00 1.27 v 0.045 ??? 1.15 ??? z ??? 0.080 ??? 2.04 b q h z l v g n a k f 123 4 d seating plane ?t? c s t u r j to?220ab case 221a?09 issue aa on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800?282?9855 toll free usa/canada japan : on semiconductor, japan customer focus center 2?9?1 kamimeguro, meguro?ku, tokyo, japan 153?0051 phone : 81?3?5773?3850 mac16hc/d literature fulfillment : literature distribution center for on semiconductor p.o. box 61312, phoenix, arizona 85082?1312 usa phone : 480?829?7710 or 800?344?3860 toll free usa/canada fax : 480?829?7709 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : http://onsemi.com order literature : http://www.onsemi.com/litorder for additional information, please contact your local sales representative.
|
